-
ASTM D6109 Test Fikstürü
ASTM D6109 – These test methods are suitable for determining the flexural properties for any solid or hollow manufactured plastic lumber product of square,
rectangular, round, or other geometric cross section…
-
ASTM D6128 Test Fikstürü
ASTM D6128 covers the apparatus and procedures for measuring the cohesive strength of bulk solids during both continuous flow and after storage at rest.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz -
ASTM D6195 – Standard Test Methods for Loop Tack
ASTM D6195 specifies a few procedures to measure quick stick adhesive strength.
This test is different from a peel test because the tape is not given enough time or pressure to fully…
-
ASTM D624 – Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
ASTM D624 – Elastomer Tear Strength Test Fixture
ASTM D624 – This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
Vulcanized rubber and…
-
ASTM D6241 –Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D6241 test method is a test used to determine the puncture resistance of geotextiles and similar products.
The method is very similar to ASTM D4833, where a test specimen is secured into a…
-
ASTM D6252 – Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
ASTM D6252 – This test method covers the measurement of the peel adhesion of pressure-sensitive label stocks.
This test method gives a measure… -
ASTM D6272 – Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D6272 – This test method covers the determination of flexural properties of unreinforced and reinforced plastics, including high-modulus composites and electrical
insulating materials in the form of rectangular bars molded…
-
ASTM D6287 Test Fikstürü
ASTM D6287 covers equipment and techniques for cutting film and sheeting specimens for testing.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz -
ASTM D6364 Test Fikstürü
ASTM D6364 covers the procedures for evaluation of the deformations of a geosynthetic or combination of geosynthetics (that is, geocomposite
(excluding geotextiles, geomembranes, and geosynthetic clay liners)) under short-term compressive loading.
Bilgi… -
ASTM D638 – Tensile Properties of Plastics
ASTM D638 – This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test
specimens when tested under defined conditions…
-
ASTM D6415 – Measuring the Curved Beam Strength of a Fiber-Reinforced Polymer-Matrix Composite
ASTM D6415- Testing Fixture
ASTM D6415 Tesing fixture is useful to indicate the curved beam strength of a continuous fiber – reinforced composite material.
For the test run it is necessary to use…
-
ASTM D6484 – Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
ASTM D6484 – This test method determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced
by high-modulus fibers.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
- TR | EN
- Tel : 0 (312) 394 28 68
- WhatsApp: 0546 437 05 06