-
ASTM D6195 – Standard Test Methods for Loop Tack
ASTM D6195 specifies a few procedures to measure quick stick adhesive strength.
This test is different from a peel test because the tape is not given enough time or pressure to fully…
-
ASTM D624 – Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
ASTM D624 – Elastomer Tear Strength Test Fixture
ASTM D624 – This test method describes procedures for measuring a property of conventional vulcanized rubber and thermoplastic elastomers called tear strength.
Vulcanized rubber and…
-
ASTM D6241 –Static Puncture Strength of Geotextiles and Geotextile-Related Products Using a 50-mm Probe
ASTM D6241 test method is a test used to determine the puncture resistance of geotextiles and similar products.
The method is very similar to ASTM D4833, where a test specimen is secured into a…
-
ASTM D6252 – Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
Peel Adhesion of Pressure-Sensitive Label Stocks at a 90° Angle
ASTM D6252 – This test method covers the measurement of the peel adhesion of pressure-sensitive label stocks.
This test method gives a measure… -
ASTM D6272 – Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials by Four-Point Bending
ASTM D6272 – This test method covers the determination of flexural properties of unreinforced and reinforced plastics, including high-modulus composites and electrical
insulating materials in the form of rectangular bars molded…
-
ASTM D6287 Test Fikstürü
ASTM D6287 covers equipment and techniques for cutting film and sheeting specimens for testing.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz -
ASTM D6364 Test Fikstürü
ASTM D6364 covers the procedures for evaluation of the deformations of a geosynthetic or combination of geosynthetics (that is, geocomposite
(excluding geotextiles, geomembranes, and geosynthetic clay liners)) under short-term compressive loading.
Bilgi… -
ASTM D638 – Tensile Properties of Plastics
ASTM D638 – This test method covers the determination of the tensile properties of unreinforced and reinforced plastics in the form of standard dumbbell-shaped test
specimens when tested under defined conditions…
-
ASTM D6415 – Measuring the Curved Beam Strength of a Fiber-Reinforced Polymer-Matrix Composite
ASTM D6415- Testing Fixture
ASTM D6415 Tesing fixture is useful to indicate the curved beam strength of a continuous fiber – reinforced composite material.
For the test run it is necessary to use…
-
ASTM D6484 – Open-Hole Compressive Strength of Polymer Matrix Composite Laminates
ASTM D6484 – This test method determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced
by high-modulus fibers.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz -
ASTM D6484 Test Fikstürü
ASTM D6484 determines the open-hole compressive strength of multidirectional polymer matrix composite laminates reinforced by high-modulus fibers.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz -
ASTM D6496 Test Fikstürü
ASTM D6496 covers the laboratory determination of the average bonding strength between the top and bottom layers of a sample of a geosynthetic clay liner (GCL).
Bilgi Almak İçin Lütfen Bizimle <a…</a…
- TR | EN
- Tel : 0 (312) 394 28 68
- WhatsApp: 0546 437 05 06