Ürünler | Page 50 of 76 | ParsRos Malzeme Test Cihazları

ISO 10275 – Tensile Strain Hardening Exponent of Metal Sheets and Strips

0 out of 5

ISO 10275 specifies a method for determining the tensile strain hardening exponent of flat products (sheet and strip) made of metallic materials.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 10319 – Geosynthetics Wide Width Tensile Test

0 out of 5

ISO 10319 describes an index test method for the determination of the tensile properties of geosynthetics (polymeric, glass, and metallic), using a wide-width strip.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 10319 Test Fikstürü

0 out of 5

ISO 10319 describes an index test method for the determination of the tensile properties of geosynthetics (polymeric, glass, and metallic), using a wide-width strip.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 10328 – Structural Testing of Lower Limb Prostheses

0 out of 5

ISO 10328 specifies procedures for static and cyclic strength tests on lower-limb prostheses which typically produce compound loadings by the application

of a single test force.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 10334 Test Fikstürü

0 out of 5

ISO 10334 – Specifies the dimensions and mechanical properties along with test methods for malleable wires used in sutures and other surgical applications.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 10477 – Polymer Based Crown and Veneering Materials

0 out of 5

ISO 10477 classifies polymer-based crown and veneering materials used in dentistry and specifies their requirements.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 1099 Test Fikstürü

0 out of 5

This ISO standard specifies the conditions for carrying out axial, constant-amplitude, force-controlled fatigue tests at ambient temperature on metallic specimens, without

deliberately introduced stress concentrations.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11040-4 Fixtures for Testing Pre-filled Glass Syringes

0 out of 5

This ISO standard applies to Tubing-glass barrels (single-chamber design) for injection preparations, and sterilized subassembled syringes ready for filling.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11608-3 Needle Based Injection System Testing

0 out of 5

ISO 11608-3-specifies the functional and design considerations for containers to be used with needle-based injection systems (NIS) that fulfil the specifications

of ISO 11608-1.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11644 – Test for Adhesion of Finish

0 out of 5

ISO 11644 specifies a method for measuring the adhesion of the finish to leather or the adhesion between two adjacent layers of the finish.
Bilgi Almak İçin Lütfen Bizimle İletişime Geçiniz
ISO 11782 – A Metal Corrosion Fatigue Testing

0 out of 5

This ISO Standard provides instruction on corrosion fatigue testing of metals and alloys in aqueous or gaseous environments and is concerned with cycles to failure testing.
Bilgi Almak İçin Lütfen Bizimle <a…</a…
ISO 12106 – Metallic Materials Axial-Strain-Control Fatigue Testing

0 out of 5

ISO 12106 specifies a method of testing uniaxially loaded specimens under strain control at constant amplitude, uniform temperature and a strain ratio of

R = -1. Low cycle fatigue tests.
Bilgi Almak…